B&M Fabrications Arctic Cat ProClimb Skinny Board Pre Order

[B&M Fabrications]

Should have more info this weekend on them. Been held up on a few things in the shop lately.

Sent from my SM-G928V using Tapatalk

 

[B&M Fabrications]

1-" raised from bottom of stock outer rail.
What you guys were thinking? Raising it more is going to make reproduction harder by getting into the limits of the bender.

Stock


New version.

 

[Chewy22]

I think that looks good, 1" from bottom.

 

[CO 2.0]

Agreed looks good. Any more than 1" higher and it will limit the footwell size too much

 

[roni87]

Working on a Sunday eh. How do they attach on the drop brackets?

 

[B&M Fabrications]

Same as stock back there. Cats are actually higher than the poo there. Just fat and low in the center. We work all the time lately.

Sent from my SM-G928V using Tapatalk

 

[B&M Fabrications]

Actually the stock cat outer rail hangs down below the board a bit so by going to this design the rail is up a little higher in the rear too.

Sent from my SM-G928V using Tapatalk

 

[WyoBoy1000]

I am helping someone install the boards cat sells, I think bdx makes them. What a joke those are, f ing ridiculous, bad fit, hard to install cheap azz boards.

 

[B&M Fabrications]

 

[scratley]

Looking good! When are planning on shipping the prepaid ones?

 

[B&M Fabrications]

Soon. Got the jigs done yesterday and welded this set to go to Wyo for Denver this weekend. We are going east for the NH show and will be back in the shop Wednesday to finish building all the pre orders. Hopefully ship the following week. We all ended up getting sick lately and have been dragging big time. Running a little behind but running hard now.

 

[CO 2.0]

I'm going to try to get them powder coated Thursday/Fri AM then getting them on w/ Wyo on Fri

 

[CO 2.0]

FYI For anyone going to the Denver Snow Show this weekend.

Front Range Arctic Cat did not get a booth inside this year. A black limited 2016 with these boards on will be on display outside in the swap meet area.

 

[Chewy22]

Soon. Got the jigs done yesterday and welded this set to go to Wyo for Denver this weekend. We are going east for the NH show and will be back in the shop Wednesday to finish building all the pre orders. Hopefully ship the following week. We all ended up getting sick lately and have been dragging big time. Running a little behind but running hard now.

Awesome - looks good. Crazy looks like the boards will arrive before the sled..........

 

[Chewy22]

I'm going to try to get them powder coated Thursday/Fri AM then getting them on w/ Wyo on Fri

Post up pics after the install.

 

[Rinker]

CO- do you and Wyo plan on videoing the install so you can throw it on YouTube? I'll see you guys at the show on Saturday. Thanks for getting this done!

 

[CO 2.0]

Will try to at least gets pics. We will be rushed tomorrow evening. Boards still arent here so prob just gonna secure them just enough for the show so we can take them back off and powdercoat them next week.

 

[B&M Fabrications]

UPS says out for delivery as of 315 this morning.

Sent from my SM-G928V using Tapatalk

 

[CO 2.0]

Boards are on for the show. Only sucked panels in on one side for the show so people can see the difference from stock panel width. Didn't fully rivet them on so they could be taken off next week for powder coat. But secured enough for people to stand on them. The foot well plates need to be cut as shown, and we had to drill new holes on the bottom to line them up. Also need another hole drilled for the inside bolt on the top. B&M, just have the outside hole pre-drilled for the upper foot well plate. The one on the inside will need to be done by the installer as each install might take a different spot to drill the other hole. They are definitely 1" higher on the outside rail. Looks great. We also did a 12-14 1/2 turn screw in the panel to suck the panels in even further and also allow the side panel to fit better. We did minor trimming to the lower panel to snug against the outer board rail, and also on the inside where a notch on the panel hits the oil tank.

Overall Wyo (Mac), Front Range Arctic Cat, and I are very happy with these boards. Best on the market now for this sled. WAY easier to install over the polaris pro boards. B&M's welds are beautiful. Very consistent.

 

[RACINSTATION]

Good work boys. I think these are going to be a great addition to the PROCLIMB chassis this year. Looking forward to trying to keep up with them Polaris boyz.......