• I am getting worn out moving your "For sale" threads, including loosely veiled sales pitches for "How much is it worth) or Wanted to buy to the swapmeet.

    Unless it is in the thread for this here in the 900 section...I will no longer be moving them for you as I have been in the past.

    Some days are silly how many for sale ads pop up.

    If I see it, it will get deleted.

    I try to help you...please try to help me.

    Thanks.
  • I've received emails and PM's asking me about "Group Buys" and promotions.

    A Group Buy here on SnoWestOnline.com would be a situation where a normal member (non vendor or mfg) personally collects orders from other members. That member then uses those orders to negotiate a better price with the Vendor/Mfg for HIS/HER "Group" of buyers.

    Here is an example of a viable "Group Buy"

    http://www.snowestonline.com/forum/showthread.php?t=269222

    A promotion that has the words "Group Buy" in the title is still a promotion, and from the rules that were handed down to me by Harris Publications is that non-advertisers cannot run promotions or open sales programs on the forums outside of the swapmeet.

    If a members wants to become a group buy manager, maintain a thread and collect the funds and negotiate a group buy... as a member, you are welcome to do that as long as you are not attached to the business of the vendor or Mfg.

    If you are a vendor/MFG and you want to offer an EXCLUSIVE "SnoWestOnline ONLY" promotion that is exclusive to snowest readers, please contact me and you'll be able to put it up in the Polaris forums.

    Also, before any vendors/mfgs get all "riled up" over this know that the moderators are strictly volunteers and do not receive a dime from any advertising $$ spent on this site.

    As ALWAYS, since DAY ONE of me becoming a moderator, I have pioneered, supported and encouraged vendors and mfgs in getting the word out to our readers with "New Product Announcements.

    Have a great season.

    From this point on, all vendors/mfg's promoting Pre-Season tiered sales programs, in the Polaris Forums, that are not paid advertisers will be appropriately moved to the swapmeet section of the forums.

    MH

05 RMK 900

May 6, 2018
3
0
1
31
Edson, AB
Ok dudes, first time poster long time reader. I’ve been working on this 05 rmk for a few months. I’ll try to sum up the backstory quickly but I fear it’s going to be a novel, but I bought this sled in the winter and rode it once. Flashed the egt probe at me. I shut it down and checked, sure enough previous owner had it disconnected. Connected the probe and carried about my ride. It was cold out. -20c. So it took a while to warm up. It was kinda funny in the low end with power cutting out but immediately ran great. Rode it for a couple hours. All seemed well. My buddy rode it the following day quickly with about the same results. Did a lot of research on the sled (a lot, I still do daily) so I thought tps or harness. I set up the tps to factory spec and proved it’s functional throughout its entire band with my oscilloscope. While I had it out, I probed the harness and found the signal to drop out. Groovy I thought. Bought a new pigtail and replaced it. I replaced the throttle and oil cable at this time. I noticed many repairs in the main harness at this time. And thought I solved my original issue. While I had the sled in the shop doing this work, I also installed the slp head I bought to use as well. I thought it would compliment the slp pipe and can quite well. Fueled it up with 50/50 ethanol free 91 and VPC11 with a little premix and installed new ngk plugs and a brand new egt probe for the hell of it. Sled was ready to go otherwise. And found I had very poor performance. Plugs looked very black and oily. While I had the head off I noticed the top end looked very poor. Piston skirts and cyl walls were notably worn. So I said ok and I went ahead and bought myself a new main harness and fuel filter and tested fuel pressure. All of which was ok. So then I went and bought myself a wrecked rmk with what I was told was a good running engine. Plugs looked nice when I pulled them and the top end was looking great. So I did the swap, installed the slp head on the second engine. And idled it on the stand to op temp to bleed coolant, revved it up a few times. Noticed a few spots of oil on the shop floor. Checked the plugs and sure enough they’re black and oily. I’m at a loss, the pump is set up and arm returns perfectly. Seems odd the same issue is happening on two engines. Any advice on where to go next with the diagnosis? This engine starts and idles just fine, as did the prior one. Perfect idle rpm.. I’m starting to think the Center seal is ironically blown on both engines...
 
May 6, 2018
3
0
1
31
Edson, AB
I should add, I want to rule out the stator on engine 1, ohmed out perfect. I used engine 1s reeds in engine 2.Used engine 2s injector harness and ignition harness. They looked to be better. I also used engine 1s intake boots on engine 2 as they looked to be recently replaced and the ones on 2 were scorched. Exhaust valves functioned on both engines. I also know for a fact I did not starve either engine for oil. I bled it all perfectly. There was prior other electrical problems, shorts in the main harness from the bar riser pulling the harness into the rider select area, found this upon the third ride. And the 3x yellow connector was making poor contact. Repaired this and all electrical issues appeared to be resolved st this point. Good lights, added heated grips are working great. I wonder if the ECM took a hit from all that going on and it’s just running rich for some reason. Going to swap ecms and capacitors and tps. Will rule out every electrical component to me. Engine 1 had 110 psi on both sides at 3000ft. Top end was torched for sure. Lol. It’s getting closer though. Just thought I’d share my experience thus far and see if you all have some insight!
 

Attachments

94fordguy

Well-known member
Staff member
Lifetime Membership
Nov 26, 2007
14,501
5,099
113
34
Yakima, Wa.
Looks like a good project! I'd fill the oil bottle full and see if the level drops, that would indicate a bad center seal. I'm not sure how much oil it would take to foul a plug, my sled is currently running 18:1 on oil... I've tried without success to lean it out on oil, I think the pump is just worn out and puking way too much oil into the engine, however it hasn't caused me any running issues yet so I've let it be. Good luck with your project, I'm just short of 6700 mountain miles on my 05 166 now!
 
Premium Features