Rpm composites g4 economy kit

[camyoung603]

Just got my kit plan on putting it on this weekend so stoked easily over 1/4 "

"Kit provides essential heavy duty protection to fragile Chain Case, Brake Rotor, and Front Cooler. Parts install by slipping guards under body panels, keeping leading edges protected and unable to catch on ground objects.Easliy use in conjunction with BRP and other aftermarket plastic skidplates. parts are constructed using epoxy, carbon fiber, Kevlar[emoji2400], and woven e-glass."

Sent from my SM-N975U using Tapatalk

 

[Adam12]

I'm happy I picked up the full kit a couple of years ago. Prices sure have gone up! Great kit though . .. nice to have some armor down there.

 

[Summit74]

Nice! Just got a call from Raffi yesterday, awesome guy w/ great customer service, he was getting ready to ship out my 2020 expert full skid plate! I tried to use my old one but the 2020 tunnel parts were different. Hopefully I will be able to reuse this one. Will post it up when I get it installed.

 

[camyoung603]

My buddy just put his on and the fit and finish is amazing would have payed double for his parts !

Sent from my SM-N975U using Tapatalk

 

[Summit74]

That’s sweet, who’s front bumper is that, fits the skid plate pretty good.
Yes I would have gone with the economy kit had I not had a old one to sell. Also after having the full plate on my 2017 and knowing the stuff I hit, looking at the scratches in the old skid plate (it takes a hard hit just to scratch the thing) I was convinced I needed the full plate. Only downfall is they are heavier than the doo plastic skid plate but worth the weight penalty. I am convinced his skid plate prevented at least one insurance claim each season.

 

[camyoung603]

I ordered my 2020 freeride with the brp full plate if I had done a little more research I would have held off and got the full carbon plate [emoji34] the front bumper is a backwoods bmp he had them tack but not weld the lower mounting plates then we waterjet out new plates to make it compatible with the rpm plate then waterjeted out nylon spacers to prevent any excessive wear or scratching. My buddy has a 4x4x8 powder coat oven so we got the closest match and did both bumpers it's super rugged and looks mint.if anyone is looking for the color code or name of the powder hit me up

Sent from my SM-N975U using Tapatalk

 

[camyoung603]

Got it installed wasn't to bad at all

Sent from my SM-N975U using Tapatalk

 

[Blainelukens]

Camyoung603 how long did it take to get yours. I can‘t tell from your pics but say you didn’t run the BRP skid how well does belly pan cover fit? I’m thinking about the economy kit as that’s cheaper than an insurance claim for me. I think the full skid is awesome but for a grand it doesn’t make since to me since I have insurance.

 

[camyoung603]

I had them in under a week and I ordered them 4 days before Christmas! If you run the kit without the skid plate all the rpm plate slide under the plastics so you can't have a rock or a stick grab a edge and rip it off

Sent from my SM-N975U using Tapatalk

 

[jcjc1]

I installed the economy kit on my 2020 Freeride and as mentioned above, it's an easy install. Plenty of room between the chassis and BRP skidplate for the cooler guard.

 

[Blainelukens]

Thanks for the response. I want to run it alone without anything else, my understanding is the factory plastic piece on each side of the sled covers the front of the chain case and brake rotor.
I am curious about the center piece on the belly pan, is that covered on the sides? How tight does it fit in the front where the red circle is on the image I attached? I wish the website showed it with all the plastic on the sled. Anyone have a pic?