Freeride 34”.

[snosumitcsr]

Anyone tried the 34” zbroz kit for the Freeride and using the stock shocks?


Sent from my iPhone using Tapatalk

 

[turboless terry]

I was told shocks won't clear. Fox has resi shocks that will

 

[caper11]

I think the Zbros kit has an upper arm design that allows the stock shocks to clear.


Sent from my iPhone using Tapatalk

 

[jcjc1]

yep, have the zbros billet kit on my '23 freeride. not going back to the 35" stance.

 

[snosumitcsr]

From what I gather you have to get the billet uppers to use the stock Freeride shocks. Does this raise the front a bit?


Sent from my iPhone using Tapatalk

 

[jcjc1]

no, it's just an a-arm. i wasn't looking specifically to have billet parts but the billet uppers are required to clear the freeride's factory resy shocks.

 

[snosumitcsr]

no, it's just an a-arm.

But it’s shorter, doesn’t it make the shocks slightly too long and in essence raise the sled slightly?


Sent from my iPhone using Tapatalk

 

[jcjc1]

But it’s shorter, doesn’t it make the shocks slightly too long and in essence raise the sled slightly?


Sent from my iPhone using Tapatalk

you'll never notice the effect of that small of a height difference while riding. i've had too much scotch to figure out any geometry at this point in time.

 

[duncan76]

I put my raptor resi. Off my 22 summit x on my 24 expert no issues

 

[SKIDOO EXPERT]

Anyone tried the 34” zbroz kit for the Freeride and using the stock shocks?


Sent from my iPhone using Tapatalk

I swapped my 2024 Freeride 36” front end to a 34” using stock parts (upper, lower, and tie-rods). The factory shocks won’t clear so I went with FOX Float QS3 Lightweight from IcAge.

 

[straightup]

You have to run the billet upper an arm kit to clear factory shocks. Standard chrome moly will fit with fox QS3.


Sent from my iPhone using Tapatalk

 

[Trolltech]

Skidoo/Lynx G4,G5 34

Introducing the Trexfab 34" High Clearance A-Arm Kit, specially designed for Skidoo G4, G5, and Lynx snowmobiles. Crafted with Durability in mind, this A-Arm kit is an essential upgrade for riders seeking optimal performance in high-altitude snowy mountain environments. Key Features: Chromoly...

www.trex-fab.com

They told me this fit with org. freeride/shredder re shocks

 

[jcjc1]

nice to have options. i didn’t see if the trexfab kit comes with tie rods like the Zbros does but I was able to use the stock tie rods anyway.

 

[burnz]

I'd imagine the stock arms off of a 25 expert would clear the freeride resi now that it has externals as well if you prefer a stock option

 

[caper11]

I'd imagine the stock arms off of a 25 expert would clear the freeride resi now that it has externals as well if you prefer a stock option

They are different shocks than the freeride.


Sent from my iPhone using Tapatalk

 

[Dogmeat]

Call them and ask them to sell you the lowers that don't cause you to lose turning radius. They're still conviently not bothering to mention that on their website when you order the G4/G5/Lynx 34" lowers from them.

I figure I lost about 12 degrees of turning radius when I put their lowers on my Lynx last year.

 

[jcjc1]

sounds like the OP is on a freeride, not a lynx.

 

[burnz]

They are different shocks than the freeride.


Sent from my iPhone using Tapatalk

yes it has pro 36 instead of pro 40s. however I would still imagine that they are pretty damn similar and the new upper arm would also clear the pro 4o resi