Z
Does anyone know how to make the gauge show coolant temperature? It does have this function correct?
coolant temperature display?
- Thread starter zebiraross
- Start date
Gauge shows low to high but no numbers on it
S
That's right. Number of bars. Just like fuel gauge. Wish it had a reading. Thermostat appears to open at 4 bars if my memory serves me right. I always let it warm up till it goes to four bars then drops to three before I let er rip, or five then four.....it's been awhile..
Z
Thanks
There is a temp module you can get from the dealer.
Z
With it, will it digitally show temp? Guess this is it:
http://ski-doo.shptron.com/p/engine-temperature-module?pp=20
http://ski-doo.shptron.com/p/engine-temperature-module?pp=20
Last edited:
I don't think it does show the temp digitally which is what I want too...maybe somebody can shed some light and confirm it still with the temp module will only display the temp in the form of "bars"
Z
The temp module from the dealer is what makes the bars show up on the pod. I belive in 13 the x's came with it, and the sp's you had to buy the module to make the temp guage function. not sure on the 14's
A
I Have a 13 x and it came with the bar temp display I did not put any temp module in but would also like to see a number display instead of bars
I installed the module on my 12 with the understanding it would show temperature, no luck bars only. So I have an operating range but no numbers.
I think that is as good as we get!!!!
I think that is as good as we get!!!!
T
i can activate the temp gauges, lap recorded and a few other features on the multifunction gauges by reprogramming the cluster.
im not certain on what specific sleds the numerical read out will work on but i was able to activate it on mine and another guys 2013 RS cluster
im not certain on what specific sleds the numerical read out will work on but i was able to activate it on mine and another guys 2013 RS cluster
T
Sylvan Lake, MI
PM for info
i know for sure that 2010 gauge clusters will not accept the numerical gauge but the bars will work
PM for info
i know for sure that 2010 gauge clusters will not accept the numerical gauge but the bars will work
B
Can you explain reprogramming the cluster?
T
people send me their clusters, i plug them into my sled, hook up to my system activate the features, write the file to it and i send it back
i have activated alot of fuel gauges for the guys with race sleds. i just discovered the numerical read out last week, but have activated the bar temp gauges for a bunch of people
i have activated alot of fuel gauges for the guys with race sleds. i just discovered the numerical read out last week, but have activated the bar temp gauges for a bunch of people
Last edited:
the advice I've received from fellow Doo riders is if the top bar isn't lit up and you're not getting flashing lights, just don't worry about it. I do try to keep the bars as close to 3-4 as possible by staying in the loose stuff but that is not always easy or even possible depending on how long the ride into the zone is...
T
here is the temp scale 2 visible bars is 50*, 3-86*, 4-104*, 5-140*, 6-158*, 7-167*, 8-176*, 9-194*
in F*
The scale is on 9 bars.
Normal temp. for 2-strokes should be between T4 and T5 (42-45 degrees C).
Normal temp. for 4-strokes should be between T4 and T5 (75-78 degrees C).
in F*
The scale is on 9 bars.
Normal temp. for 2-strokes should be between T4 and T5 (42-45 degrees C).
Normal temp. for 4-strokes should be between T4 and T5 (75-78 degrees C).
Last edited:
T
i can confirm 2010 renegades 600 etec and 800r's, 2011 race sleds cannot, and that 2013 race sled can accept the numerical read out
Similar threads
