07 dragon carl's 910 big block

troyby · Dec 18, 2010

Well, I lost the motor on my o7 d7 and polaris wouldnt warranty it because i had a pipe on it. I just happen to have a Carl's 910 sitting here so i'm going to put it in. i'm also going to install a 162 3.0 camo extreme and better boards.
Here is what i'm starting with.

troyby · Dec 20, 2010

small snag

I just ran into a small snag in the build. I was hoping to use a fuel pickup off of an 06 600 carb sled but the hole size in the fuel tank is different. Any ideas on the best route to take. I can either 1) pull all the electric fuel pump stuff out and run an old style hose and filter to the back of the tank or 2) figure out a way to make the new style pickups work if its possible. Has anyone tried this?

troyby · Dec 21, 2010

parts are in

well, I got a call today and more parts are in. I should have almst everything here. The better boards are installed. I need to pick up the WE shocks from getting repressurized, new hyperfax, tunnel extension, anti stab kit and the new drivers should be pressed on the drive shaft.

I did run into another snag. the 162 new style ce track has the little nubs just like the powder claw track. I called avid and they said to just trim off the little nubs. I would have rather put the other drivers on but time is getting short. need this running soon. maybe I'll switch them next year. I'll post more install pics tomorrow.

RMK4life · Dec 26, 2010

This sounds like its going to be one fun little hot rod!! Keep up the posts and the good work!

diamonddave · Dec 27, 2010

troyby said:
I did run into another snag. the 162 new style ce track has the little nubs just like the powder claw track. I called avid and they said to just trim off the little nubs.

That's interesting...Is this a 3.0 Pitch Camo???

diamonddave · Dec 27, 2010

Cool build btw...

troyby · Dec 27, 2010

diamonddave said:
That's interesting...Is this a 3.0 Pitch Camo???

yes, its 3.0 pitch. i guess it was built as an artic cat replacement track.
i'll run out and get some pics of my progress in a bit.

troyby · Dec 28, 2010

new parts

here are the new drivers and track.

troyby · Dec 28, 2010

better boards and track installed

got the better boards and track installed. The chain case has to come off to put the drive shaft on with the avid drivers. The nubs had to be trimmed off with a razerblade to clear the drivers.
i also put a tunnel extension on from slp to clear the 162 track. SLP anti stab kit installed and Hyper fax is installed. Rail extenstion from Tracks USA.

Now to Prep the motor.

troyby · Dec 29, 2010

Carl's Cycle 910

Here is the motor. Its a Carl's Cycle 910 on an Indy Dan prepped bottom end.

troyby · Dec 30, 2010

installed motor

I installed the motor today and its a very tight fit. Brad from power addiction built the motor plate and fit the motor. He did an outstanding job. I will be running either an IQR or an m-7 belt. he had to move the motor a little to clear the water pump and the steering shaft. He also raised the rear to clear the jack shaft. I had to grind a little off one carb to miss the steering.

The coolant lines are hooked up and ready and the fuel system is ready.

DragonFreak · Dec 31, 2010

That is a very sweet build. I have a buddy that is going to be moddin a 700 and puttin it in the Dragon chassis. Brad does awesome work. I think you should add the 09 front end

troyby · Jan 1, 2011

DragonFreak said:
That is a very sweet build. I have a buddy that is going to be moddin a 700 and puttin it in the Dragon chassis. Brad does awesome work. I think you should add the 09 front end

its got zbros a-arms and a good bumper. What would I gain from the 09 front end? I'm not sure what the difference is.

harrysmith500 · Jan 2, 2011

hey this is a rad build, I'd love to drop by and see it some time. Im a bountiful native.

troyby · Jan 2, 2011

lets ride

harrysmith500 said:
hey this is a rad build, I'd love to drop by and see it some time. Im a bountiful native.

it should be ready by next weekend. come on out and see the maiden voyage.

troyby · Jan 2, 2011

progress

the clutches are on and lined up. pipes are on everything is hooked up.
will get some gas in it and fire it up this week sometime.
I hope i got the wiring correct.

harrysmith500 · Jan 4, 2011

Big ole pipes, looks like those stingers will humm.

ragincajun · Jan 4, 2011

who did the pipes!? i have been thinkin about throwin a 903 or a 910 or something similar into my 09 D8...im getting sick of the electronics!!! sweet build!!!

1200psi · Jan 4, 2011

Looks good my man thanks for the dibs on the plate install. I am still interested in some of your 700 parts if you want to sell them.

Brad

troyby · Jan 6, 2011

CPI

ragincajun said:
who did the pipes!? i have been thinkin about throwin a 903 or a 910 or something similar into my 09 D8...im getting sick of the electronics!!! sweet build!!!

CPI in morgan utah made the slp hillclimber pipes fit.

07 dragon carl's 910 big block

Active member

Active member

Active member

Member

Chilly’s Mentor

Chilly’s Mentor

Active member

Active member

Active member

Active member

Active member

Well-known member

Active member

Well-known member

Active member

Active member

Well-known member

Well-known member

Well-known member

Active member

Similar threads