For support please email or pm Christopher christopher@snowestonline.com



Upgrade to Premium
Ski-Doo: TURBO Turbo discussion for Ski-Doo aftermarket turbo sleds
Reply
 
Share Thread Tools Display Modes
  #1  
Old 01-17-2017, 09:38 AM
Mwenzel Mwenzel is offline
Currently: Not set.
Join Date: Jan 2017
Location: New Hampshire
Basic Member
Age: 29
Posts: 33
Thanks: 4
Thanked 2 Times in 2 Posts
Rep Power: 0
Mwenzel is an unknown quantity at this point
Default 2015 etec w/ silber kit

Installed my silber kit last night. I am located in the north east so low elevation riding. For fuel I am running a 50/50 mix of 110 and 93. The plan is to run 3lbs of boost to start, but the kit came only with a 7lb spring. So I test fired only with that. 3lb is on the way. On initial start up the ARF gauge reads 14.5 not long after dips down fully rich then goes fully lean. This is during idle only. When I give her throttle she goes right back in the 14.5 range. Anyone know if this is normal or not?
Attached Thumbnails
Click image for larger version

Name:	IMG_2274.jpg
Views:	171
Size:	218.5 KB
ID:	279148   Click image for larger version

Name:	IMG_2270.jpg
Views:	122
Size:	152.0 KB
ID:	279149   Click image for larger version

Name:	7292DAF4-.jpg
Views:	121
Size:	91.6 KB
ID:	279150  

Reply With Quote


Rate this post: Yes | No
  #2  
Old 01-17-2017, 10:35 AM
DUKHTR3 DUKHTR3 is online now
Currently: Not set.
Join Date: Nov 2007
Age: 33
Posts: 493
Thanks: 123
Thanked 107 Times in 86 Posts
Rep Power: 10407263
DUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond repute
Default

It's completely normal. The etec idle is very lean.

Sent from my E6782 using Tapatalk
Reply With Quote


Rate this post: Yes | No
The Following User Says Thank You to DUKHTR3 For This Useful Post:
Mwenzel (01-17-2017)
  #3  
Old 01-17-2017, 02:19 PM
Mwenzel Mwenzel is offline
Currently: Not set.
Join Date: Jan 2017
Location: New Hampshire
Basic Member
Age: 29
Posts: 33
Thanks: 4
Thanked 2 Times in 2 Posts
Rep Power: 0
Mwenzel is an unknown quantity at this point
Default

Are there typically much changes that need to be made to the controller? The instructions don't give a whole heck of a lot of insight. If anyone has some baseline settings for 0-2000 ish ft the love would be real

Last edited by Mwenzel; 01-17-2017 at 02:34 PM.
Reply With Quote


Rate this post: Yes | No
  #4  
Old 01-17-2017, 05:19 PM
DUKHTR3 DUKHTR3 is online now
Currently: Not set.
Join Date: Nov 2007
Age: 33
Posts: 493
Thanks: 123
Thanked 107 Times in 86 Posts
Rep Power: 10407263
DUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond repute
Default

I am my 3rd season on my silber etec. After 2 season of messing with the dobeck box and chasing my bottom bog. This season I am running redline box from turbo performance and it's running awesome. My advice is turn the dobeck box into wall art and get a hold of Bryce and buy a redline box

Sent from my E6782 using Tapatalk
Reply With Quote


Rate this post: Yes | No
The Following User Says Thank You to DUKHTR3 For This Useful Post:
brycter (01-23-2017)
  #5  
Old 01-17-2017, 05:22 PM
DUKHTR3 DUKHTR3 is online now
Currently: Not set.
Join Date: Nov 2007
Age: 33
Posts: 493
Thanks: 123
Thanked 107 Times in 86 Posts
Rep Power: 10407263
DUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond repute
Default

Also looks like your coolant hose is on the waste gate. It will melt. I know from experience. IRoute it between the turbo and waste gate. Then go up to coolant bottle. I would also put wire loom on it.

Sent from my E6782 using Tapatalk
Reply With Quote


Rate this post: Yes | No
The Following User Says Thank You to DUKHTR3 For This Useful Post:
Mwenzel (01-17-2017)
  #6  
Old 01-17-2017, 05:44 PM
Mwenzel Mwenzel is offline
Currently: Not set.
Join Date: Jan 2017
Location: New Hampshire
Basic Member
Age: 29
Posts: 33
Thanks: 4
Thanked 2 Times in 2 Posts
Rep Power: 0
Mwenzel is an unknown quantity at this point
Default

I will check that out for sure, it just went in. Still need to neaten up a few things with zip ties etc
Reply With Quote


Rate this post: Yes | No
  #7  
Old 01-20-2017, 07:10 PM
Mwenzel Mwenzel is offline
Currently: Not set.
Join Date: Jan 2017
Location: New Hampshire
Basic Member
Age: 29
Posts: 33
Thanks: 4
Thanked 2 Times in 2 Posts
Rep Power: 0
Mwenzel is an unknown quantity at this point
Default

Where are people mounting the stock air sensor? Tube that goes to the turbo or the one that goes into the carbs?
Reply With Quote


Rate this post: Yes | No
  #8  
Old 01-20-2017, 09:40 PM
DUKHTR3 DUKHTR3 is online now
Currently: Not set.
Join Date: Nov 2007
Age: 33
Posts: 493
Thanks: 123
Thanked 107 Times in 86 Posts
Rep Power: 10407263
DUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond reputeDUKHTR3 has a reputation beyond repute
Default

Put it on the one that goes to the turbo and hooks to air box.

Sent from my E6782 using Tapatalk
Reply With Quote


Rate this post: Yes | No
  #9  
Old 11-03-2017, 09:57 PM
cycle cycle is offline
Currently: Not set.
Join Date: Jan 2008
Basic Member
Age: 46
Posts: 91
Thanks: 2
Thanked 1 Time in 1 Post
Rep Power: 11
cycle is an unknown quantity at this point
Default

Any pics of your new Gen 2 controller installed? Thinking about doing the same
Reply With Quote


Rate this post: Yes | No
  #10  
Old 11-07-2017, 09:20 AM
Mwenzel Mwenzel is offline
Currently: Not set.
Join Date: Jan 2017
Location: New Hampshire
Basic Member
Age: 29
Posts: 33
Thanks: 4
Thanked 2 Times in 2 Posts
Rep Power: 0
Mwenzel is an unknown quantity at this point
  #11  
Old 11-07-2017, 07:34 PM
cycle cycle is offline
Currently: Not set.
Join Date: Jan 2008
Basic Member
Age: 46
Posts: 91
Thanks: 2
Thanked 1 Time in 1 Post
Rep Power: 11
cycle is an unknown quantity at this point
Warning You Must be a registered member and logged in to view this response.

Click Here to Register

  #12  
Old 11-08-2017, 01:46 AM
xpturbo600 xpturbo600 is offline
Currently: Not set.
Join Date: Oct 2009
Basic Member
Posts: 80
Thanks: 0
Thanked 41 Times in 23 Posts
Rep Power: 1902135
xpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond repute
Warning You Must be a registered member and logged in to view this response.

Click Here to Register

  #13  
Old 11-08-2017, 07:48 AM
Mwenzel Mwenzel is offline
Currently: Not set.
Join Date: Jan 2017
Location: New Hampshire
Basic Member
Age: 29
Posts: 33
Thanks: 4
Thanked 2 Times in 2 Posts
Rep Power: 0
Mwenzel is an unknown quantity at this point
Warning You Must be a registered member and logged in to view this response.

Click Here to Register

  #14  
Old 11-08-2017, 08:08 AM
Mwenzel Mwenzel is offline
Currently: Not set.
Join Date: Jan 2017
Location: New Hampshire
Basic Member
Age: 29
Posts: 33
Thanks: 4
Thanked 2 Times in 2 Posts
Rep Power: 0
Mwenzel is an unknown quantity at this point
Warning You Must be a registered member and logged in to view this response.

Click Here to Register

  #15  
Old 11-09-2017, 02:19 AM
xpturbo600 xpturbo600 is offline
Currently: Not set.
Join Date: Oct 2009
Basic Member
Posts: 80
Thanks: 0
Thanked 41 Times in 23 Posts
Rep Power: 1902135
xpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond reputexpturbo600 has a reputation beyond repute
Warning You Must be a registered member and logged in to view this response.

Click Here to Register

The Following User Says Thank You to xpturbo600 For This Useful Post:
Mwenzel (11-09-2017)
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Thread — 2015 silber turbo kit Thread Starter — BryanD Forum — Turbos/Superchargers (Swapmeet) Replies — 1 Last Post — 03-24-2016 11:21 AM
Thread — 2015 silber turbo xm kit - self lube, v-band, top of the line kit! Thread Starter — bmiller1985 Forum — Turbos/Superchargers (Swapmeet) Replies — 1 Last Post — 02-22-2015 03:48 PM
Thread — Skidoo 800 Etec Xm V-band Silber kit Thread Starter — standup06 Forum — Turbos/Superchargers (Swapmeet) Replies — 4 Last Post — 01-09-2015 05:55 PM
Thread — Silber XM etec kit Brand NEW $5k Thread Starter — Wheel House Motorsports Forum — Turbos/Superchargers (Swapmeet) Replies — 1 Last Post — 02-27-2014 01:23 PM
Thread — 2014 SILBER XM ETEC TURBO KIT Thread Starter — hobbes Forum — Turbos/Superchargers (Swapmeet) Replies — 3 Last Post — 02-13-2014 02:37 AM

All times are GMT -6. The time now is 04:49 PM.












no new posts