FOX FLOAT II ?

captain x · Dec 18, 2013

I have a set of FOX FLOAT II's on an '07 Summit. Front Shocks

Will they fit and work on an '11 XP?

I checked the length and the stock 11XP and FOX FLOAT II's are both 16.5" center to center of the mounting bracket/bolt.

Thanks Guys

adam8781 · Dec 18, 2013

should bolt right on

Wowmom · Dec 18, 2013

Not to hi-jack the thread, but I have have a set coming tomorrow. What are you running your pressure at? 200# rider, mostly climbing and playing in the trees.

captain x · Dec 18, 2013

On the '07 the psi was at 150 for my son, he is about 225#. We have not had enough run time to try different settings.

snobinge · Dec 19, 2013

150psi...WOW! I am 215# and I run 50ish in the mountains and 65 on the trails. I don't run a swaybar in the Mtns.
Tom's has a guideline sheet that I'm sure you could email them for.

byeatts · Dec 19, 2013

captain x said:
I have a set of FOX FLOAT II's on an '07 Summit. Front Shocks

Will they fit and work on an '11 XP?

I checked the length and the stock 11XP and FOX FLOAT II's are both 16.5" center to center of the mounting bracket/bolt.

Thanks Guys

Send to Toms, he adds a shim to make the correct length, He can also revalve at the same time, Money well spent.There are performance upgrades such as the new high flow piston for little $$.

Cracker · Dec 19, 2013

snobinge said:
150psi...WOW! I am 215# and I run 50ish in the mountains and 65 on the trails. I don't run a swaybar in the Mtns.
Tom's has a guideline sheet that I'm sure you could email them for.

If you are at 150# they have the wrong spring in them .

chumbilly1 · Dec 19, 2013

Pretty sure that the psi is the spring on a float2. Imho

byeatts · Dec 20, 2013

chumbilly1 said:
Pretty sure that the psi is the spring on a float2. Imho

There is a short Negative spring inside which sets static height and helps with shutter bumps, The air takes over from there, The valving out of the box is set Very Harsh however after re valved and high piston they and feather plush. Tom has these dialed.

backcountryislife · Dec 20, 2013

byeatts said:
There is a short Negative spring inside which sets static height and helps with shutter bumps, The air takes over from there, The valving out of the box is set Very Harsh however after re valved and high piston they and feather plush. Tom has these dialed.

The spring is a factor, but couldn't cause anywhere near that kind of PSI IMO

byeatts · Dec 20, 2013

captain x said:
On the '07 the psi was at 150 for my son, he is about 225#. We have not had enough run time to try different settings.

You sure bout that. 150 is the shox max pressure if I recall on the front floats. I run 70 max.

xpspenziv · Dec 21, 2013

Here ya go.
http://cdnmedia.endeavorsuite.com/i...4d-9113-60d45f149823/Shock Settings Chart.pdf

Search

FOX FLOAT II ?

captain x

Member

adam8781

Free Member

Wowmom

Active member

captain x

Member

snobinge

Free Member

byeatts

Well-known member

Cracker

Active member

chumbilly1

Well-known member

byeatts

Well-known member

backcountryislife

Well-known member

byeatts

Well-known member

xpspenziv

Well-known member

Similar threads