Muffler mounted in place.
Installation and Review: SKINZ Under the Tunnel Nytro Exhaust Kit (Review Now Posted)
- Thread starter christopher
- Start date
The new muffler uses the original mounting hardware from the OEM mount.
And yes, I dented the muffler.
Dropped it right on the tailpipe!
And yes, I dented the muffler.
Dropped it right on the tailpipe!
Just waiting on the cover plate to come back and get riveted into place and this project will be finished.
S
rear bumper
Just wondering if top profile of the tunnel extension is the same on the 2010 as an 08. Would prefer that bumper opposed to the one skinns makes for the 08 Nytro.
Just wondering if top profile of the tunnel extension is the same on the 2010 as an 08. Would prefer that bumper opposed to the one skinns makes for the 08 Nytro.
Couldn't tell ya.
I have a 2009 and a 2010 Nytro.
My Cover Plate arrived this afternoon at the office.
Have to go pick it up tomorrow.
I have a 2009 and a 2010 Nytro.
My Cover Plate arrived this afternoon at the office.
Have to go pick it up tomorrow.
A
Can't wait to see this. This is the exact kit that I want to put on my sled this year, but I haven't researched it enough to get the pro's and con's to it.
Can you share any?
Thanks!!
Can you share any?
Thanks!!
Got a working camera finally.
Will go take a photo NOW.
Just a minute.
Will go take a photo NOW.
Just a minute.
The Sled as it is now.
With the new cover Plate
Closeup
Underside of plate showing the installation of the heat reflective material Skinz installed to protect the powdercoating from excessive exhaust heat.
With the new cover Plate
Closeup
Underside of plate showing the installation of the heat reflective material Skinz installed to protect the powdercoating from excessive exhaust heat.
A
Well...I'd better get mine ordered this weekend! Thanks for sharing!! Great pictures of the details!
:face-icon-small-hap
:face-icon-small-hap
I plan on getting it drilled and prepped to install this weekend.
Just need to finish polishing my tunnel first.
Just need to finish polishing my tunnel first.
Chris, what's up with your install here? Are there problems?
I am going to drill and Rivet it in place this weekend.
Things here on SnoWest have just taken ALL of my free time lately!
Things here on SnoWest have just taken ALL of my free time lately!
Lookin good Chris!
Beginning the install now.
A
Can't wait to see pics! 
After laying the plate over the hole, the first thing to do was to mark the mounting point for the exhaust hanger bolt on the underside of the cover plate, where the hole had to be drilled through it.
Drilled it and set the bolt in Place
Drilled it and set the bolt in Place
In order to get the cover plate into the correct position, there are a series of bolts that are left over from the old seat mount that have to be removed.
Center Rivet has to be drilled out from under the tunnel, and always spun on me, so I used vice grips to hold it.
There are FOUR of these pairs that have to be removed.
Center Rivet has to be drilled out from under the tunnel, and always spun on me, so I used vice grips to hold it.
There are FOUR of these pairs that have to be removed.
On my 2010 Nytro 162 SE, one of these pairs was a bear. The connecting plate went under the mount for the Oil Cooler. Only way to get this out was to either drill all the rivets for the oil cooler and drop it, or to cut the plate in half and slide it out.
I inserted a couple screw drivers to pull the plate away from the tunnel and took a grinder and sliced through the plate to release it.
Once it was sliced in half, and the center rivet drilled it, it slid under the oil cooler and out the back with no further trouble.
Once it was sliced in half, and the center rivet drilled it, it slid under the oil cooler and out the back with no further trouble.
Next I positioned the rear of the cover and center punched a hole for the drill bit.
Set a rivet.
And began drilling all the remaining holes all the way around the plate.
And set the Clecos in place as I drilled each hole to ensure the plate didn't budge while drilling
Set a rivet.
And began drilling all the remaining holes all the way around the plate.
And set the Clecos in place as I drilled each hole to ensure the plate didn't budge while drilling
Similar threads
- Locked
