<table width="100%" align="center" class="tborder" id="post4126004" border="0" cellspacing="1" cellpadding="10"><tbody><tr><td class="thead">
01-26-2018, 06:36 PM <!-- / status icon and date -->
</td></tr><tr><td class="alt2" style="padding: 0px;"><!-- user info --> <table width="100%" border="0" cellspacing="10" cellpadding="0"><tbody><tr><td nowrap="nowrap">
sumtinwong <script type="text/javascript"> vbmenu_register("postmenu_4126004", true); </script>
<!--ADDED BY BRIAN FOR VB STATUS--> Currently:
Not set. Edit
<!--END ADDED BY BRIAN FOR VB STATUS-->
Basic Member
</td><td width="100%"> </td><td nowrap="nowrap" valign="top">Join Date: Oct 2016
Location: north pole alaska
Age: 39
Posts: 580
Thanks: 170
Thanked 127 Times in 93 Posts
Rep Power: 7826202
</td></tr></tbody></table><!-- / user info --> </td></tr><tr><td class="alt1" id="td_post_4126004"><!-- HEAVILY MODIFIED BY BRIAN FOR PAID/FREE THING --> <!-- Forum IDs are the list of restricted forums --> <!-- LOCKED FORUMS BRIAN locked_forums --> <!-- message, attachments, sig --> <!-- icon and title -->
<hr size="1" style="color: rgb(232, 232, 232); background-color: rgb(232, 232, 232);"><!-- / icon and title --> <!-- message --> so I started in to this with a 2x4 and like it was posted above without a heavy guy on the sled you are just yarding it around like a rag doll! so I decided to do it a little more methodic. I decided before I proceeded that I was going to lift the toe loop until it started to tear just to figure out how far a guy could lift it without needing to weld or just junk the loop. as you can see I propped a 2x2 under the rail just to help relieve some of the stress on the rail, I cut it long to give some upward pressure. slid a small jack from a old car in the toe loop and proceeded to spread. the first loop I heated with a torch to about 120-130 degrease just enough to be pretty worm but not hot as to try to not temper or harden the aluminum. the other side I did at room temp. I was able to lift the heated side to about 4 3/4-4 7/8 before it tore and when it did it just went leaving inner and outer with no kind of structural integrity left. on the cold side it only made it to 4 3/8- 4 1/2 before the same damage occurred. I am a poor aluminum welder {at best} but do have a welder that welds aluminum. managed to weld it back together good enough that I can jump on either side and get no movement. so if you choose to lift those hooks heat until they are warm and don't lift them more than more than 4 3/4 measured off the rails on a square to the bottom of the toe hook unless you plain on welding or going without the hooks. I pushed mine up until I hade 5in just because well they were all ready tore but it did seem to have plenty of room to not hook your boot in at 4 3/4. just wanted to post this in hopes it would aid someone in not getting hurt or loosing their seasons riding! good luck to all on their way to recovery!
sorry the picts are bad! toe hook on the right it stock and the one with the jack in it is at about 4 3/4 to 4 7/8 and the one with the spool gun on the rail is at 5in
<!-- / message --> <!-- attachments --> <fieldset class="fieldset"><legend>Attached Thumbnails</legend>
</fieldset>
<!-- / attachments --> <!-- edit note --> <hr size="1" style="color: rgb(232, 232, 232); background-color: rgb(232, 232, 232);">
Last edited by sumtinwong; 01-26-2018 at 06:43 PM. Reason: edit
<!-- / edit note -->
<!-- message, attachments, sig --> <!-- END MODIFIED BY BRIAN --> </td></tr></tbody></table><table width="100%" align="center" class="tborder" border="0" cellspacing="1" cellpadding="10"><tbody><tr><td class="alt2" style="padding: 0px;">
The Following 4 Users Say Thank You to sumtinwong For This Useful Post: </td></tr><tr><td class="alt1" colspan="3">
Escmanaze (01-26-2018),
HCRRider (01-29-2018),
Randman (01-27-2018),
Timbre (01-26-2018)
posted this last year it was good enough for me. lots of talk on this subject in a post Poll:
My running-board foot-loop injury: Who else has had their foot stuck in the footwell? (
1 2 3 ...
Last Page) TRS <!-- ADDED BY BRIAN FOR DATE --> - 04-17-2016
</td></tr></tbody></table>