Hands down the best ZX MOD!
- Thread starter JustinB
- Start date
S
Here is one from Dootalk
http://www.dootalk.com/forums/index.php?showtopic=393658
http://www.dootalk.com/forums/index.php?showtopic=393658
Updating to the piveting riser was by far the best mod I ever did to my 700.
By the way Cntrvl sledder I don't think your gonna like the painted arms and tunnel, snow is very much like sandpaper and it won't look that nice for very long IMHO. The boss seat was a good upgrade also but not as nice as the risers. As you can see I need better boards or something next. Also when I get in some really deep powder it starts to bog down then comes out of it when I hit some ones track any ideas there?
By the way Cntrvl sledder I don't think your gonna like the painted arms and tunnel, snow is very much like sandpaper and it won't look that nice for very long IMHO. The boss seat was a good upgrade also but not as nice as the risers. As you can see I need better boards or something next. Also when I get in some really deep powder it starts to bog down then comes out of it when I hit some ones track any ideas there?
Any idea what those WKRP boards will sell for? I am in the middle of a tunnel project and fully intend to install or make something like these!
The others will clear the snow fine _ I am sure, but I ***_u_me that these tie in on the side of the tunnel for support as well?
Also - I don't understand "dropping the tunnel 1"."
What does that mean?
You dropped the rear suspension an inch maybe?
.
The others will clear the snow fine _ I am sure, but I ***_u_me that these tie in on the side of the tunnel for support as well?
Also - I don't understand "dropping the tunnel 1"."
What does that mean?
You dropped the rear suspension an inch maybe?
.
Ahh I did it last year as well. One side I did two layers of clear coat and I lost no paint on the other side I did one and had a tiny bit come off. So this year I took them off Blasted them down too the metal and powder coated them and added three coats of clear coat! I am also painting my 800's yellow. I am not doing the tunnel I polished it instead:face-icon-small-hap
C
Put a team clutch on best bang for your buck
and anti ratchet drivers.
and anti ratchet drivers.
H
RKT head and 670x pistons to keep the compression.and NOS. Then a 174 track and go slay what you want.
This summers mods
1) boss seat
2) 154 16in xp track
3) mountainfit hoods grill inserts (wicked sweetness)
4) mountain addictions gas rack
5) polished tunnel
6) team clutch (best clutch ever)
1) boss seat
2) 154 16in xp track
3) mountainfit hoods grill inserts (wicked sweetness)
4) mountain addictions gas rack
5) polished tunnel
6) team clutch (best clutch ever)
M
ZX seats are easy enough to modify. I took my stock seat, shortened it by removing the storage area, and narrowed the foam a bit for my knees.
You could always add foam on top for a rise if you wished.
Cheapest mod so far :face-icon-small-hap
You could always add foam on top for a rise if you wished.
Cheapest mod so far :face-icon-small-hap
Z
You could change your gearing. I went from my stock 19/43 (high mark) to a 17/48. You may think thats a little too low but I like it, gets your track turning in a hurry. Rips from 0 to 50! Great for deep powder, slow speed torque is great and i can crawl at 5mph through the trees without slipping my belt. It will still pull 78mph fully shifted out on the road. I dont miss stock gearing at all. Im sure my belt temps are lower, it runs higher on the primary so more grip, less slip. Anyway my two cents
You guys looking for something like the WRP BetterBoards , RSI has cutouts to rivet to your tunnel and then cut the hole out in the tunnel, they come in sections so you can add as many as you want, I put a couple in my boys Racer-X tunnel on each side up in front where the snow builds up, should probably add a couple more on each side. Look on RSI website for info, would fit on any tunnel.
Last edited:
Best ZX Mod
http://www.snowestonline.com/forum/showthread.php?t=195817
Hope this link works. This guy has taken a rev seat and mounted it on a zx chassis. Looks pretty good and might be easier than the other method in this thread. I haven't tried it myself, though. It looked like it sets you up a couple of inches or better. The taller the seat the easier it is to transfer from sitting to standing in mountain riding. Just thought I would share. Good-luck!
http://www.snowestonline.com/forum/showthread.php?t=195817
Hope this link works. This guy has taken a rev seat and mounted it on a zx chassis. Looks pretty good and might be easier than the other method in this thread. I haven't tried it myself, though. It looked like it sets you up a couple of inches or better. The taller the seat the easier it is to transfer from sitting to standing in mountain riding. Just thought I would share. Good-luck!
L
Gearing.
My ( 2005 ) ZX Renegade-X 800H.O. ( Riding height 1200 - 3500 Feet )
* Gearing 22/43
* Track 144"x15"x1,75"
* BRP 9tooth anti rachet driver.
* Floating secondary clutch.
* Dynamoe Joe clutch kit.
* Carlisle belt , "803" / "821" ( Way better milage then BRP belt !! )
* BRP 5" riser.
* Ohlins shocks
* Skinz Ultra-Q can
* SLP Powder pro skies
* Boyesen X-Rage reed kit.
* RK-Tek head.
* ZX-"X" chassi.
.
My ( 2005 ) ZX Renegade-X 800H.O. ( Riding height 1200 - 3500 Feet )
* Gearing 22/43
* Track 144"x15"x1,75"
* BRP 9tooth anti rachet driver.
* Floating secondary clutch.
* Dynamoe Joe clutch kit.
* Carlisle belt , "803" / "821" ( Way better milage then BRP belt !! )
* BRP 5" riser.
* Ohlins shocks
* Skinz Ultra-Q can
* SLP Powder pro skies
* Boyesen X-Rage reed kit.
* RK-Tek head.
* ZX-"X" chassi.
.
Last edited:
